Original Drill Dispenser Cabinets

The Huot Step Drill Dispenser gives you plenty of organizational capacity in a compact, handy size.Store your step drills (and center drills if you use them) in tidy compartments that are each roomy enough to hold multiple bits. Use our pre printed labels or create your own using our pro label holder system (included) Adjacent compartments can hold additional step drills of the same size, different sizes, corresponding center drills, etc. Pre-labeled for 1/8″ to 1-3/8″ sizes

Read more less

Taps and dies counter display Holds these sizes: 1/8-27 NPT, 4-40 NC, 6-32 NC, 8-32 NC 10-24 NC, 10-32 NF, 12-24 NC, 1/4-20 NC *1/4-28 NF, 5/16-18 NC, 5/16-24 NF, 3/8-16 NC 3/8-24 NF, 7/16-14 NC, 7/16-20 NF, 1/2-13 NC 1/2-20 NF, 9/16-12 NC, 9/16-18 NF, 5/8-11 NC *5/8-18 NF, 3/4-10 NC, 3/4-16 NF, T-Handle Wrench 0 to 1/4″ All steel welded outer shell Clear, hinged polycarbonate front for high visibility and shatterproof durability Lockable with own set of two keys Steel drill gauge on top assures correct sizing of drills All compartments display drills vertically to use less counter space, and are rounded to make small drills readily accessible Attractive, bright red epoxy finish to enhance drill sales Compact, takes less counter space Makes excellent use of counter space for impulse sales

Read more less

#1 to #60 reamers, 5 drawer dispenser Wire gauge sizes #1 to #60 Decimal equivalents also listed Ideal where compact space is a must 4 stackable models for reamer organization in Fractional, A to Z, wire gauge sizes, over/under dowel pin sizes One piece drawer slide Finished with tough epoxy powder coating

Read more less

S&D Drills 1″ to 1-1/2″ assorted Holds 2 each Reduced shank S/D bits From 1″, 1-1/32, 1-1/16, 1-1/8, 1-5/32, 1-3/16, 1-1/4, 1-5/16, 1-3/8, 1-7/16, 1-1/2 Label holders on drawer fronts permit easy, quick identification and inventory check One piece drawer slide Stackable with other cutting tool storage cabinets to save space Finished with tough epoxy powder coating

Read more less

S&D Drills 33/64″ to 63/64″ by 1/64ths Holds 2 each Reduced shank S/D bits From 33/64ths to 63/64ths by 64ths Label holders on drawer fronts permit easy, quick identification and inventory check One piece drawer slide Stackable with other cutting tool storage cabinets to save space Finished with tough epoxy powder coating

Read more less

Wall mounting with doors for up to 3 Original dispenser cabinets. Secure your inventory using wall mounted cabinet. Heavy 18 gauge prime steel powder coated in our exclusive Huot battleship gray powder. Holds up to 3 Original dispenser cabinets Locks using your own padlock Shipped KD and supplied with carriage bolts and nuts for easy assembly Provide protected storage for your valuable cutting tool inventory Wall mounted on 16″ centers using your own mounting hardware Dispensers sold separately

Read more less

Tap and drill dispenser, 6-32 #36 to 1/2″-20 #29/64Stores and organizes correct drill with corresponding size tap.Holds one dozen (minimum) of each sizeTAP DRILL6 – 32, #368 – 32, #2910 – 24, #2510 – 32, #211/4 – 20, #71/4 – 28, #35/16 – 18, F5/16 – 24, I3/8 – 16, 5/163/8 – 24, Q7/16 – 14, U7/16 – 20, 25/641/2 – 13, 27/641/2 – 20, 29/64Label holders on drawer fronts permit easy, quick identification and inventory checkOne-piece drawer slideStackable with other cutting tool storage cabinets to save spaceFinished with tough epoxy powder coatingADDITIONAL INFORMATION; Weight 10.25 lbsDimensions 14.625 × 7.375 × 7.75 in

Read more less

3mm to 24mm metric tap dispenserHolds 29 popular metric sizes:3 mm x .50, 3 mm x .60, 4 mm x .704 mm x .75, 5 mm x .80, 5 mm x .906 mm x 1.00, 6.3 mm x 1.00, 7 mm x 1.008 mm x 1.00, 8 mm x 1.25, 9 mm x .759 mm x 1.00, 9 mm x 1.25, 10 mm x 1.0010 mm x 1.25, 10 mm x 1.50, 11 mm x 1.5012 mm x 1.25, 12 mm x 1.50, 12 mm x 1.7514 mm x 1.25, 14 mm x 1.50, 14 mm x 2.0016 mm x 1.50, 16 mm x 2.00, 18 mm x 2.5020 mm x 2.50, 24 mm x 3.00StackableOne piece drawer slideFinished with tough epoxy powder coatingADDITIONAL DESCRIPTION; Weight 10.50 lbsDimensions 14.625 × 7.375 × 7.75 in

Read more less

2-56 thru 12-28 tap dispenserEach size holds taper, plug, bottoming, and spiral point taps60 compartmentsHolds machine screw sizes:2-56, 3-48, 3-56, 4-40, 4-485-40, 5-44, 6-32, 6-40, 8-328-36, 10-24, 10-32, 12-24, 12-28StackableOne piece drawer slideFinished with tough epoxy powder coatingADDITONAL; Weight 10.50 lbsDimensions 14.625 × 7.375 × 7.75 in

Read more less

1/4″-20 thru 1″-12 tap dispenser Holds popular fractional sizes: 1/4″-20 NC, 1/4″-28 NF, 5/16″-18 NC, 5/16″-24 NF 3/8″-16 NC, 3/8″-24NF, 7/16″-14 NC, 7/16″-20 NF 1/2″-13 NC, 1/2″-20 NF, 9/16″-12 NC, 9/16″-18 NF 5/8″-11 NC, 5/8″-18NF, 3/4″-10 NC, 3/4″-16 NF 7/8″-9 NC, 7/8″-14 NF, 1″-8 NC, 1″-12 NF Stackable One piece drawer slide Finished with tough epoxy powder coating

Read more less

#1 to #60 wire gage drills, jobbers length• Holds full packages of each size (12 pc. Min.)• Stackable for larger inventories• One piece drawer slide for long useful life• Decimal equivalentsAdditional: Weight Weight 10.25 lbsDimensions 14.625 × 7.375 × 7.75 in

Read more less

#1 to #60 wire gage drills, stub screw machine length Holds full packages of each size (12 pc. Min.) *Stackable for larger inventories. *One piece drawer slide for long useful life. *Decimal equivalents. *Marked for screw machine length to help control inventory.

Read more less

#1 to #80 wire gage drills, jobbers length• Holds full packages of each size (12 pc. Min.)• Stackable for larger inventories• One piece drawer slide for long useful life• Decimal equivalentsAddtional; Weight 10.25 lbsDimensions 14.625 × 7.375 × 7.75 in

Read more less

Counterbore Dispenser, Original All steel cabinet with vinyl drawer dividers to help protect and separate counterbores. Stackable with all Huot “Original” style dispensers. Holds continuous pilot counterbores sizes #4, #5, #6,#8, #10, #12, ¼”, 5/16”, 3/8”, 7/16”, & ½”.

Read more less

NPT dispenser Holds all sizes of National Pipe Taps (NPT) from 1/16” to 2” Top drawer has 13 compartments; 2 for 1/16” – 27, 2 for 1/8” – 27, 3 for 1/4” – 18, 3 for 3/8” – 18, 3 for 1/2” – 14, Middle drawer has 6 compartments – 3 for 3/4” – 14, 2 for 1” – 11-1/2”, and 1 oversized compartment for 1-1/4” – 11-1/2” Bottom drawer has 2 oversized compartments – 1 for 1-1/2” – 11-1/2”, and 1 for 2” – 11-1/2” Label holders on drawer fronts permit easy, quick identification and inventory check One piece drawer slide Stackable with other cutting tool storage cabinets to save space Finished with tough epoxy powder coating

Read more less

1/16″ to 1/2″ x 64ths counter display for jobbers drills All steel welded outer shell Clear, hinged polycarbonate front for high visibility and shatterproof durability Lockable with own set of two keys Steel drill gauge on top assures correct sizing of drills All compartments display drills vertically to use less counter space, and are rounded to make small drills readily accessible Attractive, Royal Blue finish (Red shown in photo) Compact, takes less counter space Makes excellent use of counter space for impulse sales

Read more less

1mm to 6.9mm by .1mm 1mm to 6.9mm by .1mm stub Holds full packages of each size – (12 pc. Min.) Stackable for larger inventories. One piece drawer slide for long useful life. Decimal equivalents.

Read more less

1/16″ to 1/2″ x 64ths counter display for jobbers drills All steel welded outer shell Clear, hinged polycarbonate front for high visibility and shatterproof durability Lockable with own set of two keys Steel drill gauge on top assures correct sizing of drills All compartments display drills vertically to use less counter space, and are rounded to make small drills readily accessible Attractive, bright red epoxy finish to enhance drill sales Compact, takes less counter space Makes excellent use of counter space for impulse sales

Read more less

Carbide burr dispenser, popular sizes Holds the following sizes: Cylindrical 1/4″ x 5/8″, Cyl. Rad. End 1/4″ x 5/8″, Ball 1/4″ x 1/4″ Oval 1/4″ x 3/8″, Tree Rad. 1/4″ x 3/4″, Tree/Pointed 1/4″ x 3/4″ Cone/Rad. End 1/4″ x 5/8″, Cylindrical 3/8″ x 3/4″, Cyl./Rad. End 3/8″ x 3/4″ Ball 3/8″, Oval 3/8″ x 5/8″, Tree/Rad. End 3/8″ x 3/4″ Tree/Pointed 3/8″ x 3/4″, Cone/Rad. End 3/8″ x 1-1/16″, Cone/Flat End 1/4″ x 1″ Cone/Rad. End 1/2″ x 1-1/8″, Cone/Flat End 3/8″ x 1″, Cylindrical 1/2″ x 1″ Cyl./Rad. End 1/2″ x 1″, Ball 1/2″, Oval 1/2″ x 7/8″ Tree/Rad. End 1/2″ x 1″, Tree/Pointed 1/2″ x 1″, Cone/Flat End 1/2″ x 1″ One piece drawer slide Stackable Finished with tough epoxy powder coating

Read more less

A to Z reamers, 3 drawer dispenser A to Z Reamers Decimal equivalents also listed Ideal where compact space is a must 4 stackable models for reamer organization in Fractional, A to Z, wire gauge sizes, over/under dowel pin sizes One piece drawer slide Finished with tough epoxy powder coating

Read more less

1/16″ to 1/2″ reamers, 4 drawer dispenser Fractional Reamers 1/16″ to 1/2″ by 64ths Decimal equivalents also listed Ideal where compact space is a must 4 stackable models for reamer organization in Fractional, A to Z, wire gauge sizes, over/under dowel pin sizes One piece drawer slide Finished with tough epoxy powder coating

Read more less

Space saving combination dispenser The dispenser for metric taps, drills and dies. From 2.5 x .45 tap to 12.0 x 1.75 tap Top drawer holds: 2.5 x .45 tap – 2.05 drill, dies 3.0 x .50 tap – 2.50 drill; dies 3.5 x .60 tap – 2.90 drill, dies 4.0 x .70 tap – 3.30 drill, dies Room in top drawer for your T-handle wrench. Middle drawer holds: 5.0 x .80 tap – 4.20 drill, dies 6.0 x 1.0 tap – 5.0 drill, dies 8.0 x 1.25 tap – 6.70 drill, dies Bottom drawer holds: 10.0 x 1.50 tap – 8.50 drill, dies 12.0 x 1.75 tap – 10.20 drill, dies Label holders on drawer fronts permit easy, quick identification and inventory check One piece drawer slide Stackable with other cutting tool storage cabinets to save space Finished with tough epoxy powder coating

Read more less

CNC Tool Tower for 40 taper tool holdersIndividual units are 3′ tall3 shelves – 24 toolholders per shelfNylon inserts protect each tool holderSturdy 16 gauge steel constructionTool Tower should be bolted to the floor for additional securityCasters should never be used on a stacked CNC Tower as this could be extremely dangerousAdditional: Weight 65 lbsDimensions 27.3125 × 18.3175 × 36 in

Read more less

Carbide insert “original” series dispenserDesigned to keep inserts at each work centerCompact size keeps the most frequently used inserts within fingertip reachThree drawers have a moveable divider with a large fourth drawer to store tool holders and extra insertsLabel holders on drawer fronts permit easy, quick identification and inventory checkOne piece drawer slideStackable with other cutting tool storage cabinets to save spaceFinished with tough epoxy powder coating

Read more less